Various Equipment > Hydraulic Cylinders & Pumps
Royal Line 2500 psi

  • Honed tubing.
  • Heavy duty welded construction.
  • Chromed, ground and polished piston rod.
  • Ductile iron piston and gland.
  • Cross tube pin eye mounting on both ends, with grease zerks.
  • Urethane U-cup and urethane wiper in gland. O-ring/backup washers and cast iron ring for piston seals.
  • Truarc snap ring gland retainer.
  • Standard color is red.


Royal Line

Wizard Line 3000 psi

  • Honed tubing.
  • Chromed, ground and polished rod.
  • Ductile iron piston and gland.
  • Optional end fittings available.
  • Urethane U-cup and wiper.
  • Crown seal standard, 'T' seal optional.
  • Nylon wear ring on piston.
  • Thread in gland with O-ring to protect threads.
  • Standard color is gloss black.

Wizard Line

Fortress Line 3000 psi

  • Heavy duty welded construction.
  • Chromed, ground and polished piston rod.
  • Skived tubing
  • Ductile iron piston.
  • Thread-in ductile iron gland.
  • Urethane U-cup, metal encased wiper, teflon cap seal and wear ring.
  • Crosstube end fittings with grease zerks.
  • Painted highway yellow.
  • Matches closed length of Royal Line cylinders (up to 42" stroke).
  • Spacer included in longer stroke models.

Fortress Line

Sword Line 3000 psi

  • Skived/honed tubing.
  • Heavy duty welded construction.
  • Chromed, ground and polished piston rod.
  • Ductile iron piston, gland and clevis and cast steel base end.
  • Square ring gland retainer provides positive lock.
  • Urethane U-cup and urethane wiper in gland, crown seal on piston.
  • Pins, clips and cotters included.
  • Standard color is white.
  • Stroke control may be installed on 8" strokes.

Sword Line

Gladiator Line 3000 psi

  • Heavy duty welded construction.
  • Externally threaded gland cap.
  • Chromed, ground and polished piston rod.
  • Skived tubing.
  • Ductile iron piston.
  • Urethane U-cup, metal encased wiper in gland, polyurethane crown seal and wear ring on piston.
  • Standard color is highway yellow.
  • Matches closed length of Royal Line cylinders (up to 42" stroke).
  • Spacer included in lower stroke models.

Gladiator Line

3000 psi Tie Rod

  • Honed tubing.
  • Heavy duty, high strength tie rods.
  • Hardened, chromed, ground and polished piston rod will operate at full pressure through 16" stroke. (Rods on 2" and 2 1/2" not hardened.)
  • Ductile iron piston, butt, gland, and clevis.
  • Urethane U-cup and metal encased wiper on 2 1/2" and larger bore models.
  • Polyurethane crown seal on piston.
  • Pin, clips, cotters included.
  • Standard color safety yellow.
  • Stroke control may be installed on 8" stroke
  • Side ports available on request at no additional cost.
  • Nylon bearing ring on 4, 4 1/2, 5" bore models.

3000 psi Tie Rod

Majestic Line 2500 psi

  • Honed tubing (SAE-7000 and SAE-8400 series have cylinder finish tubing).
  • Chromed, ground and polished piston rod will operate at full pressure through 16" stroke.
  • Ductile iron piston, butt, gland and clevis.
  • Pins, clips and cotters included.
  • Urethane U-cup and urethane wiper in gland.
  • Standard color is red.
  • Stroke control may be installed on 8" strokes.
  • Side ports available on request at no additional cost.

Majestic Line

King Line 2500 psi

  • Honed tubing (SAE-9000 and SAE-9100 series have cylinder finish tubing).
  • Heavy duty, high strength tie rods.
  • Chromed, ground and polished piston rod will operate at full pressure through 16" stroke.
  • Ductile iron piston, butt, gland and clevis.
  • Urethane U-cup and urethane wiper in gland.
  • Pins, clips and cotters included.
  • Stroke control may be installed on 8" strokes.
  • Side ports available on request at no additional cost.

King Line

Noble Line 2500 psi, 16 " stroke

  • Same cylinder as SAE-9200, 9300 and 9400 except retracted length is 26 1/4".
  • Standard color is red.
  • Available in 3, 3 1/2, and 4" bore.

Noble Line

Imperial Line 2500 psi, 4" bore

  • Same high quality as SAE-9400, but with 2" G & P chromed piston rod for those tough applications.
  • Standard color is red.

Imperial Line

Telescopic Line

Single Acting
  • 3,000 PSI
  • 2" to 9" diameter sleeves
  • Vee packings
  • Various strokes

Double Acting

  • 3,000 PSI
  • 2 1/2" to 9 3/4" diameter sleeves
  • Vee packings
  • Various strokes

Telescopic Line

PTO

Prince PTO pumps are gear pumps with an internally splined drive shaft. They are designed to slide onto the male splines of Power Take Off shafts on agricultural tractors. The internal splines of the pump mate with the standard 540 rpm shaft (1 3/8" 6 tooth splines) or the standard 1000 rpm shaft (1 3/8" 21 tooth splines). Continuous pressure ratings are up to 2250 psi.

PTO

SP20A

The SP20A series is an SAE A 2 bolt mount family of pumps. The pumps are available in displacements from 0.400 in 3/rev to 2.014 in 3/rev. Flows range from 3.0 to 15.2 gpm at 1800 rpm (5.1 to 25.3 gpm at 3000 rpm). Continuous pressure ratings are up to 3000 psi.

SP20A

SP25A

The SP25A is an SAE B 2 bolt mount family of pumps. The pumps are available in displacements from 1.141 in 3/rev to 3.869 in 3/rev. Flows range from 8.5 to 28.7 gpm at 1800 rpm (14.2 to 48.1 gpm at 3000 rpm). Continuous pressure ratings are up to 3000 psi.

SP25A

SPD1

The SPD1 double pump consists of two pumping sections from our SP20A family of pumps. The pumps are available in all combinations of available displacements and are available with common or separate inlets.

SPD1

SPD2

The SPD2 pump is a single pump from the SP25A family of pumps with an internally splined through shaft and an SAE A 2 bolt mount pad on the rear of the pump. A pump with an SAE A 2 bolt mount and a standard 9 tooth splined shaft can be mounted to the back of the pump to form a multiple pump.

SPD2

SPD3

The SPD3 double pump consists of two pumping sections from our SP25A family of pumps. The pumps are available in all combinations of available displacements and are available with common or separate inlets.

SPD3

SP20P

The SP20P series consists of priority flow divider pumps. In a priority flow divider pump, the output of the pump is divided into two streams, a constant flow priority stream and an excess flow stream. The pumps are available in the same displacements as our SP20A family.

SP20P

SP25P

The SP25P series consists of priority flow divider pumps. In a priority flow divider pump, the output of the pump is divided into two streams, a constant flow priority stream and an excess flow stream. The pumps are available in the same displacements as our SP25A family.

SP25P

sales@tricoprusa.com Tricorp USA | P.O. Box 2779 | Palm Beach, FL 33480 USA
phone:561-804-9909 | fax:561-804-9042 | email: sales@tricorpusa.com
Copyright © 2001